Downloads

1. Absorption Vs. Ultraviolet-Visible Range Spectrophotometry
   6/19/2013

   Spectrophotometry is a technique employed when quantitative measurement and analysis of specific spectra of light is required. From simple quality assurance techniques to advanced chemical analysis, spectrophotometry is a robust and widely used process that spans multiple disciplines and industries. By Randy Klimek

2. VectorStar Family Of RF, µW, mmW VNAs - Premium Line - MS4640A Series Brochure
   5/23/2013

   The VectorStar family is Anritsu’s Premium VNA line, offering the highest overall performance on a modern platform. For Anritsu's value Line VNA, check-out the Lightning Family that offers high performance such as Dynamic Range and Port Power, at speeds suitable for most R&D applications.

3. AR’s Newly Redesigned “W” Series
   5/14/2013

   Our newly redesigned “W” Series Class A solid state amplifiers have significantly increased their value to our customers.  We have superior gain flatness, better noise figure, improved linear power margins, better efficiency, and better harmonics measured at higher powers than in previous designs.  And if that wasn’t enough we reduced the size and weight by approximately  50%.

4. Application Note: Testing S-Parameters On Pulsed Radar Power Amplifier Modules
   5/7/2013

   This Application Note describes testing S parameters under pulsed conditions with the R&S ZVA vector network analyzer, and a signal generator with pulse modulator as a signal source. An L-band radar pulsed power transistor is used as example device under test (DUT). The pulse profile mode of the R&S ZVA is used to analyze the time-dependent behavior of the DUT.

5. Datasheet: Low Cost Attenuators with Ethernet/RS-232 and Manual Control: 50BA-010-127
   4/16/2013

   The 50BA-010-127 is a configuration with two individually controlled solid-state programmable attenuators in a miniature benchtop enclosure. It operates in the 700-3000 MHz frequency range and has an impedance of 50 Ohms (nominal). For additional specifications, download the datasheet.

6. Datasheet: Low Cost Attenuators with Ethernet/RS-232 and Manual Control: 50BA-011-95
   4/16/2013

   The 50BA-011-95 setup includes four individually controlled solid-state programmable attenuators in a miniature benchtop enclosure. It covers the 200-6000 MHz frequency range and has a 0-95 dB attenuation range.

7. Pulsed Laser Wavelength Meter: 821 Series Datasheet
   3/26/2013

   The 821 series of pulsed laser wavelength meters accurately measures pulsed and CW laser wavelengths in applications involving high-resolution spectroscopy, photochemistry, cooling and trapping, and optical remote sensing. This datasheet contains a detailed description of the system, information on its features, specifications, and more.

8. Pulsed RF Microwave Frequency Counter/Analyzer: CNT-90XL
   3/11/2013

   This RF/Microwave frequency counter/analyzer can be used to measure, analyze, and calibrate microwave frequency, power, and pulsed RF time parameters like pulse width and PRI. This system features a graphical display and improved control over measurement.

9. Pulsed RF Microwave Frequency Counter/Analyzer: CNT-90XL Datasheet
   3/11/2013

   This datasheet includes a detailed description of the CNT-90XL Pulsed RF Microwave Frequency Counter/Analyzer. This system can be used in medical RF equipment testing, microwave link carrier calibration, satellite communication equipment testing, RF and microwave instrumentation calibration, pulsed, chirped, and Doppler radar testing and calibration, and much more.

10. 1P2T Solid State RF Switch: 50S-1832
    2/27/2013

    This solid state RF switch has a 1P2T configuration and operates in the 960-1300 MHz frequency range. It has an impedance of 50 Ohms nominal, a -20^oC to +70^oC operating temperature range, and more.